Showing posts with label porsche racing. Show all posts
Showing posts with label porsche racing. Show all posts

Monday, July 18, 2011

Cayenne in Action. Desktop Quality Pic.



This is the follow up email to last week pics. A friend of mine who drove his Focus SVT at the open track day grabbed this shot of the Cayenne towing, or is it 944 drafting, on the deserted HIghway 36.

Deserted except for cops who make sure you don't speed on the way to the track.

I do need to tell my friend to clean his lens though. Geez.

Sunday, July 10, 2011

Corner Balancing the SPEC Car



The last item on my list to get my SPEC 944 ready for a test day was to corner balance it.

Ideally, I should have done this before I got my alignment, but the timing didn't work out. And I knew the car would be close to balanced as it was sitting level at 4 3/4 inches at all four corners as measured from the rockers.

So, having borrowed some scales from 944 SPEC director locally, I set them up in my garage and got to work. The number I was really concerned about was my cross-weight.

Now, I won't explain, but you can find out all about corner balancing here.

Right from the get go, my cross-weight was 49.81%. Which is about perfect.

But wait, I didn't check how level my garage floor was. Checking, it was 2 inches lower in the back than the front. Oops. After leveling the scales my cross weight was 48.1%. Not good enough.

So, with some minor,(less than a quarter turn of my coil overs) on both front corners I was able to get the cross-weight to 49.51%. Ahh, good enough.

The above chart is courtesy of here. My numbers are on the left. I was not about to try and get to their perfect numbers as it is a bit of waste of time. I mean fuel load, tire wear all effect the corner balancing.

But, I am in the sweet spot and can't wait to get out on track.

Saturday, November 20, 2010

Further Adventures in 944 Torsion Bar Adjustment







Now that the racing season is over, I decided to make some of the larger changes that I refrained from during the season. I wanted to complete the races this year with basically the same set-up so I could work on my driving and get used to the tracks, not different set-ups.

The work today, it was sunny but brisk in Denver this late November Saturday, was to lower the rear of the car. I went out thinking it would be a one hour job. It took three and a half. Why? Me make stupid mistake sometimes.

So, I jack the car up, unhook the shocks and get ready to easily remove the torsion bars. Or so I thought. I had drilled holes in the rockers and affixed tabs to the torsion bars to specifically make this job easier.

But no matter what I did, I could not get the torsion bars to budge. And since they were new and well-greased I knew they should easily slide out when the splines, pressure and planets aligned. But no go.

I used the standard approach of a jack under the trailing arm to move up and down and get the torsion bars to be de-stressed. But still, they would not slide out. Even when asking for my neighbor to come over and help I could not get the bars to move. I was frustrated.

So, after two hours I jacked the car higher and removed the jack stand from under the torsion tube carrier(that is the round end that sticks out into the wheel well). I was about to call it a day. But then I decided to try removing the bar again. And it worked. WTF?

My best guess is the weight of the car on the torsion tube carrier was just enough to tweak the angle of the carrier and wedge the bar in place. Once my idiocy was uncovered I got to lowering the car. I was running at 5.5 to 5.75 inches on the rear measured ground to rocker at the seam. This was WAY HIGH for a leading 944 SPEC car. I wanted to get down to 4.5. A full inch lower. Many of the winners run 4 inches flat.

I got the passenger side in one shot. The drier side took three tries. There is no exact formula to this, just trial and error. But one trick is to make a mark on the shock, and measure form there. So, that is what I did, make a mark and jacked the trailing arm up one inch and then reinserted the torsion bar.

Just take a look at the pictures. Once inch does not sound like much but the look is dramatically different. I hope the handling is dramatically tighter. I think this will make a big difference in quick transition corners and also on the high-speed sweepers on some courses that have a big 'pucker' factor in my car as it wags its tail.

Final height adjustments will be made in the spring with my new race tires when I corner balance at the beginning of the season. There is 3/4 of an inch of adjustment available in the trailing arm set up without reindexing.

Don't clown the photos, it is riding high in front. But that is because I was too tired to lower the front down so that the car, according to Dave Dirks(my engine builder and 2010 944 SPEC national champion), is co-planer. Which in my case means 4.5 inches from ground to rocker at all four corners.

Improving a race car just doesn't happen in the race season. In fact, it is best to make the big changes during downtime so that when the season rolls around, all a racer has to do is worry about tire pressure and showing up.

Now, off to the couch to relax, rest my back and fall asleep warmed by a rather special Imperial Stout.